Porcelain has gone from a specialist request to one of the two surfaces almost every patio customer asks us about, alongside Indian sandstone. It is easy to see why. It does not need sealing, it does not stain the way natural stone does, and the colour you see on the sample is the colour you get across the whole patio.

What people are told less often is that porcelain is the least forgiving surface we lay. It is unforgiving of a poor sub-base, unforgiving of a shortcut in the bedding, and it needs a step in the installation that natural stone does not. Get all of it right and it will outlast most of the house. Get it wrong and tiles lift. This guide covers what to look for when you are choosing, and what to ask when you are being quoted.

What Outdoor Porcelain Actually Is

Porcelain paving is a manufactured tile, fired at very high temperature from refined clay so the finished product is dense, hard and almost non-porous. That very low water absorption is the source of nearly every advantage it has: it does not soak up spills, it does not host algae the way porous stone does, and water cannot get inside it to freeze and split it apart.

The key thing to know is that outdoor porcelain is not the same product as the tiles in your bathroom. External paving is 20mm thick, roughly double an internal tile, with an anti-slip surface texture built in. If a quote mentions 10mm porcelain for a garden patio, that is an indoor tile and it is the wrong product.

Why 20mm Matters

The extra thickness is not just about strength underfoot. It gives the tile enough body to be laid on a full mortar bed outdoors and to cope with ground movement, frost and the loads a garden actually sees. Thinner tiles are designed to be bonded to a rigid internal floor, not bedded on mortar over a sub-base. It is the single easiest thing to check on a quote, so check it.

Colours and Finishes

Because porcelain is manufactured, the colour range is far wider than natural stone and far more consistent. There is no batch variation to work around and no waiting to see how it weathers in. The ranges we are asked for most are:

Stone-Effect

Porcelain printed to replicate riven sandstone, limestone or slate. The better ranges use a large number of different face patterns, so you do not get the repeat that gives cheaper porcelain away. This is the choice for people who want the look of natural stone with none of the sealing.

Concrete and Cement-Effect

Flat, contemporary greys with a very subtle texture. Popular on modern extensions and new builds around Telford, and particularly effective with large-format tiles and thin joints where you want the patio to read as one clean surface.

Timber-Effect

Plank-format tiles that mimic decking boards without any of the upkeep, rot or winter slip that real timber brings. Useful next to a lawn or around a garden building where decking would be the obvious choice but the maintenance is not wanted.

Dark Tones

Charcoals, graphites and near-blacks. They look superb and they suit contemporary properties, but they show dust, pollen and water marks more than mid-tones do. Worth seeing a full slab outdoors in daylight rather than judging from a small sample indoors.

You can see the ranges we supply on our porcelain paving page and the full options on the porcelain paving options page.

Slip Resistance: The Number to Ask About

This is where a bit of technical knowledge saves you real trouble. External porcelain carries a slip rating, most commonly expressed as an R value from the ramp test. R10 is the usual minimum for outdoor use, R11 is the sensible standard for a British garden, and R12 and above is a coarse, heavily textured finish more common in commercial settings.

For a Shropshire patio that will be wet for months at a time, R11 is what we would specify as standard. It gives reliable grip in the rain without being so aggressive that it is uncomfortable underfoot or awkward to clean.

How a Porcelain Patio Is Laid

This is the section worth reading twice, because installation is where porcelain patios succeed or fail, and the differences from natural stone are the things that get skipped.

1. Excavation and Sub-base

We dig out and lay a compacted sub-base, typically MOT Type 1, to give a stable load-bearing foundation. Porcelain is rigid and unforgiving. Any settlement in the ground beneath will show as a cracked tile or a lipped joint, because the tile will not flex to accommodate it the way stone can.

2. Falls for Drainage

The patio is laid with a slight fall, around 1 in 80, running away from the house so rainwater drains off rather than pooling or tracking back to the building. Porcelain is non-porous, so every drop of rain that lands on it has to run somewhere. On stone some of it soaks in. On porcelain, none of it does, which makes getting the falls right more important, not less.

3. Priming: The Step That Cannot Be Skipped

Here is the difference that matters. Because porcelain is effectively non-porous, mortar will not bond to it on its own. The back of every single tile has to be coated with a slurry primer immediately before it goes down, so the mortar has something to grip.

Skip the primer and the tile sits on the mortar rather than being bonded to it. It looks perfect on the day. Then the first hard winter gets water into the interface, it freezes, and tiles start to lift and rock. This is comfortably the most common cause of failed porcelain patios, and it is invisible once the job is finished.

4. Full Mortar Bed

Every tile is laid on a full, solid bed of mortar. Not on five dabs under the corners and middle. Spot bedding leaves voids that fill with water, and with a rigid tile over a void you get cracking as well as rocking. It is more work and more material, and it is the right way to do it.

5. Cutting and Jointing

Porcelain is hard enough that it needs cutting wet with a diamond blade, which is slower than cutting stone and part of why the labour cost is higher. Once the tiles are down and set, the joints are filled with a suitable jointing compound and tooled to a neat finish.

Three Questions Worth Asking Any Installer

Is the porcelain 20mm external grade? What slip rating is it? And is every tile primed with a slurry primer before bedding? If a quote is noticeably cheaper than the others, the saving has usually come from one of those three, or from a thinner sub-base. None of it is visible on completion day. All of it shows up later.

What a Porcelain Patio Costs

Porcelain sits at the upper end of patio surfaces. The tiles themselves cost more than most natural stone, and the installation takes longer because of the priming and the cutting. As a general indication for Shropshire, a fully installed porcelain patio tends to work out around £110 to £170 per square metre, so roughly £2,200 to £3,400 for a typical 20 square metre patio.

Surface Installed per m2 Sealing needed? Ongoing upkeep
Porcelain £110 to £170 No Sweep and wash, check pointing
Riven Indian sandstone £80 to £120 Yes, every 2 to 3 years Sealing, algae treatment, cleaning
Sawn Indian sandstone £100 to £150 Yes, every 2 to 3 years Sealing, algae treatment, cleaning

These figures are indicative only, to give you a sense of where porcelain sits against the alternatives. Every garden is different, and access, ground conditions, levels, steps and edging all move the number, so we quote each job individually after a free site visit rather than working to a flat rate. For a wider look at outdoor surface costs, see our cost guide.

The Lifetime Cost Is Closer Than It Looks

Porcelain costs more to install, but there is no sealing to pay for every two or three years and far less cleaning. Over ten years the gap between porcelain and sealed natural stone narrows considerably. If you are choosing on budget alone, it is worth comparing the whole decade rather than just the invoice at the end of the job.

Porcelain vs Natural Stone: Choosing Between Them

Both are excellent surfaces and neither is universally better. It comes down to what you want from the garden. Our Indian sandstone guide covers the other side of this in more depth.

Porcelain Suits You If...

Natural Stone Suits You If...

Plenty of our customers use both in the same garden. Porcelain for the main terrace where easy upkeep wins, and sandstone for paths, borders and feature areas where character matters more. Have a look at our patio designs and patios and paths pages for ideas, or the Shropshire patio ideas guide for how this plays out in different property styles.

Looking After a Porcelain Patio

This is the shortest section in the guide, which is rather the point.

Our autumn and winter maintenance guide covers the seasonal routine across all surfaces.

Porcelain Patios Across Shropshire

We design and lay porcelain patios throughout the county, and the property usually points towards the right range:

Wherever you are, the fundamentals do not change. A proper sub-base, the right falls, every tile primed, and a full mortar bed. Browse our project galleries to see completed work, or the paving slabs page for the wider range.

Common Questions We Get Asked

How much does a porcelain patio cost in Shropshire?

As a general indication, a fully installed porcelain patio works out around £110 to £170 per square metre, so roughly £2,200 to £3,400 for a typical 20 square metre patio. That is a guide rather than a quote. Access, ground conditions, levels, steps and edging all affect the price, so we quote every job individually after a free site visit.

Does porcelain paving need sealing?

No. Porcelain is fired at very high temperature and is effectively non-porous, so there is nothing for a sealer to penetrate. This is one of its main advantages over natural stone, which needs resealing every two to three years. The joints between the tiles still need checking and maintaining, though.

Is porcelain paving slippery when wet?

Not if you specify the right product. External porcelain carries a slip rating, and R11 is the sensible standard for a British garden, giving reliable grip in the rain. Always ask for the slip rating rather than assuming. Polished or smooth-finish tiles are for indoor use and should never be laid outdoors.

Why does porcelain need to be primed before laying?

Because it is effectively non-porous, mortar will not bond to it on its own. The back of every tile must be coated with a slurry primer immediately before bedding so the mortar has something to grip. Skipping this is the most common cause of porcelain patios failing, and the problem only appears after a winter or two when tiles begin to lift and rock.

What thickness of porcelain do I need for a patio?

20mm. External porcelain paving is 20mm thick, roughly double the thickness of an internal floor tile, with an anti-slip texture built in. If a quote specifies 10mm porcelain for a garden, that is an indoor tile and it is not suitable for laying on mortar over a sub-base outdoors.

Can porcelain be used for a driveway?

Standard 20mm patio porcelain is designed for foot traffic, not vehicles. There are thicker paving-grade products, but for a driveway we would normally steer you towards block paving or resin bound, which are engineered for the loads and give a better result. Porcelain is at its best as a patio, terrace or path surface.

Ready to Plan Your Patio?

The best next step is a site visit. We need to see the space, check the levels and drainage and understand how you want to use the area before we can price it properly. A good quote will tell you the tile thickness, the slip rating, the sub-base and the bedding method, not just a headline figure.

We design and install patios across Shrewsbury, Telford, Oswestry, Market Drayton, Whitchurch, Newport and all of Shropshire, with a written workmanship guarantee on everything we do. Get in touch and we will arrange a convenient time to come and have a look.

Shropshire Driveways & Landscaping

A family business serving Shrewsbury, Telford, Oswestry and all of Shropshire for over 29 years. Driveways, patios, fencing and landscaping, done properly.

Thinking About a New Patio?

Free, no-obligation quotes and honest advice on porcelain and natural stone across Shrewsbury, Telford, Oswestry and all of Shropshire.

Get Your Free Quote